FiPy Side Trans GX
FiPy LoRa Sigfox LTE-M Development Board TopFiPy LoRa Sigfox LTE-M Development Board Bottom

FiPy

49.00

Imagine 5 networks in one perfectly-formed, same-small-foot-print-as-WiPy- LoPy-and SiPy, IoT development board. MicroPython enabled. Featuring WiFi, Bluetooth, LoRa, Sigfox and dual LTE-M (CAT M1 and NBIoT) the FiPy gives access to all the world’s LPWAN networks on one tiny board.

Available on back-order

Product Description

Note: This is to preorder for shipping end of June/July 2017

Imagine 5 networks in one perfectly-formed, same-small-foot-print-as-WiPy- LoPy-and SiPy, IoT development board. MicroPython enabled. FiPy includes WiFi, Bluetooth, LoRa, Sigfox and dual LTE-M (CAT M1 and NBIoT) the FiPy gives access to all the world’s LPWAN networks on one tiny board.

Get on with a board that gives you full flexibility during testing, install, deployment and even later when you want to switch real-time your airtime network provider. You can switch when the time is right for you or set some parameters that will do so automatically.

PLEASE NOTE: Pycom modules are powered by the NEW and FEATURE PACKED Espressif ESP32 chip. As a result our firmware is evolving constantly as the ESP32 IDF matures. Regular firmware updates are therefore provided.

 

FiPy Features

– Powerful CPu
– Five networks: WiFi, BLE, cellular LTE-CAT M1/NB1, LoRa and Sigfox
– 1KM WiFi range
– MicroPython enabled
– Fits in a standard breadboard (with headers)
– Ultra-low power usage: a fraction compared to other connected microcontrollers

Processing

– Espressif ESP32 SoC
– Dual processor and WiFi radio system on chip
– Networking processor handles the WiFi connectivity and the IPv6 stack
– Main processor is entirely free to run the user application
– An extra ULP-coprocessor that can monitor GPIOs, the ADC channels and control most of the internal peripherals during deep-sleep mode while only consuming 25uA

Interfaces

– 2 x UART, 2 x SPI, I2C, micro SD card
– ANalog channels: 8×12 bit ADCs, 2×8 bit DAC
– Timers: 2×64 bit with PWM with up to 16 channels
– DMA on all peripherals
– GPIO: Up to 22

Hash / Encryption

SHA, MD5, DES, AES

WiFi Networking

802.11b/b/n 16mbps

Bluetooth

Low energy and classic

RTC

Running at 32KHz

Range

Node range: Up to 50km

Security & Certifications

– SSL/TLS support up to 1.2
– WPA Enterprise security
– AES encryption engine

Memory

– RAM: 4MB
– Flash Memory: 8MB
– GPIO: Up to 22
– Hardware floating point acceleration
– Python multi-threading

Power

– Voltage Input: 3.3V – 5.5V
– 3v3 output capable of sourcing up to 400mA

Sigfox Operating Frequencies

RCZ1 – 868MHz(Europe)

RCZ2 – 902MHz (US, Canada and Mexico)

RCZ3 – (Japan and Korea)

RCZ4 – 920-922MHz (ANZ, Latin America and S-E Asia)

Sigfox Specification

– TI CC1125NarrowbandTransceiver

– Class 0 device. Maximum Tx power:

  • – +14dBm (Europe)
  • – +22dBm (America)
  • – +22dBm (Australia and New Zealand)

– Node range: Up to 50km

– Sigfox pre-certified (October 2016)

– Power

  • – Sigfox (Europe): 17mA in Rx mode, 47mA in Tx mode and 0.5uA in standby
  • – Sigfox (Australia, New Zealand and South America):
  • 24mA in rX mode, 257 mA in Tx mode and 0.5uA in standby

Bluetooth Networking

– Low energy and classic

– Compliant with Bluetooth v4.2 BR/EDR and BLE specification

– Class-1, Class-2 and Class-3 transmitter without external power amplifer

– Enhanced power control

– +10dBm transmitting power

– NZIF receiver with -98 dBm sensitivity

– Adaptive Frequency Hopping (AFH)

– Standard HCI based on SDIO/SPI/UART

– High speed UART HCI, up to 4 Mbps

– BT 4.2 controller and host stack

– Service Discover Protocol (SDP)

– General Access Profile (GAP)

– Security Manage Protocol (SMP)

– Bluetooth Low Energy (BLE)

– ATT/GATT

– HID

– All GATT-based profile supported

– SPP-Like GATT-based profile

-BLE Beacon

-A2DP/AVRCP/SPP, HSP/HFP, RFCOMM

– CVSD and SBC for audio codec

– Bluetooth Piconet and Scatternet

LoRa Operating Frequencies

– 868MHz(Europe) at +14dBm maximum

– 915MHz (North and South America, Australia and New Zealand) at +20dBm maximum

LoRa Specification

– Power consumption: 10mA Rx, 28mA Tx

– LoRaWAN stack – Class A and C devices

– Node range: Up to 40km

– Nano-gateway: Up to 22km (Capacity up to 100 nodes)

LTE-M Operating Frequencies

– 34 bands supports from 699Mhz to 2690Mhz (Total world-wide support)

LTE-M Specification

– One single chip for both CAT M1 and NB1 (yes, only one chip)

– 3GPP release 13 LTE Advanced Pro

– Supports narrowband LTE UE categories M1/NB1

– Integrated baseband, RF, RAM memory and power management

– Reduced Tx power class option

– Peak power estimations: TX current = 420mA peak @1.5Watt RX current = 330mA peak @1.2Watt

– Data rates:

  • – 300 kbps DL
  • – 375 kbps UL (LTE Cat M1 in 1.4 Mhz, HD-FDD)
  • – 40 kbps DL
  • – 55 kbps UL (LTE Cat M2 in 200 kHz, HD-FDD)

WiFi Networking

– Up to 1km range

– 802.11b/g/n 16mbps

– Power: 12mA in active mode, 5uA in standby

Size

55m x 20mm x 3.5mm (Without Headers)

Weight

– 7g
– 31g (Packaged)

Additional Information

Weight 0.007 kg
Dimensions 5.5 x 2.0 x 0.35 cm
Weight

7 g

Dimensions

55 x 20 x 12 mm